May 21, 2014 · From this point on, router #1 will be called ‘Primary’ and router #2 will be referred to as the ‘Secondary’ or ‘client’ router. Option #1: Connect Two Routers. With option #1, you connect the LAN port of the client router to the LAN port of the primary router (do not use the WAN port on the client router).

Connect two, three, four, five routers in one network, extend wired local network, increase Wi-Fi wireless coverage. Serge's Computer Services Toronto and GTA. We provide exceptional quality online remote computer repair services on demand. Nov 15, 2019 · Now router 1 is out of the way for port forwarding and triggering as all incoming connections are now being forwarded to router 2. Now in router 2 I can setup my port forwarding & triggering rules just like normal. So here is a quick step by step. Step 1. Login into your Router Step 2. Types of Dual-band Network Routers Selectable Dual-band Network Routers. As the name implies, this type of dual-band router gives you the option to choose whether to broadcast a 2.4 GHz or a 5 GHz Wi-Fi network. Meaning, you cannot use both at the same time. You have to switch one on and one off based on your preferences or needs. Primary DNS 192.168.0.1 LAN IP Setup LAN TCP/IP Setup IP Address 192.168.1.1 IP Subnet Mask to 255.255.255.0 RIP direction is None RIP version is disabled Use Router as DHCP Server Starting IP Address 192.168.1.2 Ending IP Address 192.168.1.19. actiontec-----set lan ip to 192.168.0.1 (default) disable dhcp under Advanced Setup, DHCP Server State Jul 07, 2019 · If you are using broadband routers like Asus, Belkin, Microsoft, Siemens, Edimax, etc., then chances are higher that you may require 192.168.2.1 IP address now and then. 192.168.2.1 is the default IP Address for most of the home or business routers to access administrator panel. Jun 04, 2014 · Firstly, I live in a 2.5 storey home and the current wireless signal in the highest floor is very weak. So, I will be installing 2 Lan cables from the room on the ground floor where the unifi modem and router is located to the top floor. Lan cable 1 will connect to the BTU port for IPTV. Lan cable 2 will be connected the new new router. Router B (192.168.1.1) has home computers, storage etc (sensitive information) which I would like to keep secure. I would like guest and other devices on other routers to not have access to devices on this router Router C (192.168.2.1) has mostly media devices. Everything works fine now in terms of basic internet access, etc.

Apr 16, 2009 · hello, i have a problem using my d link dir-300 wireless router my computer are one connect to the dsl.and i have a interconnected computer using my switch hub.up an using the wireless network .I connect my laptop to the wireless d link and it is connected but with out internet connection .I connect a cross over to the port 1 of the the d-link and the other side to the switch .con you help me

You also add port 23 to vlan 100 and port 24 to vlan 200. Now on each interface on the router connected to each port configure one subnet. On router-1 192.168.1.1/24 and router-2 192,168,2.1/24. Don't forget to assign PC-1 an ip address in the range of 192.168.1.2/24 and PC-2 192.168.2.2/2' HTH Step 3: Connecting the 2 nd Router to the 1 st Router. Now that both the routers have been configured, there is only one small thing left and that is to connect them. To do this, you will need an ethernet cable. Depending on how far away these routers will be to each other, the ethernet cable might need to be quite long.

Aug 15, 2016 · When I set the Border Router up with IP 10.10.1.1, the LAN set up the IPs for the DHCP Server from 10.10.1.2 to 10.10.1.254. Seems like this is the correct thing to do.

For the sake of readability, from now on I will refer to "Router #1" and "Router #2" as "R1" and "R2" respectively. Every router does NAT (Network Address Translation), and has both an internal IP address and an external IP address. The external IP address is the one that connects that router to the WAN (Wide Area Network). Usually the WAN is Under "My Network->Network Connections->Broadband Connection->SettingsSettings" I changed the "Internet Protocol" to "obtain ip address automatically" to "no ip address". 5. Rebooted secondary router, and then once I verified all changes, I attached the coax cable to the secondary router and for about 1-2 minutes it looked like everything worked.